настройка Realtek rtl-8139

Доброго времени суток.

Никак не удается настроить сетевую карту Realtek rtl-8139 в FreeBSD 4.10. Согласно
документации ей соответствует модуль if_rl.

Ситуация следующая:

$ dmesg
...
rl0: <RealTek 8139 10/100BaseTX> port 0xd000-0xd0ff mem 0xcfffdf00-0xcfffdfff
irq 5 at device 17.0 on pci0
rl0: couldn't map interrupt
device_probe_and_attach: rl0 attach returned 6
...
$

Я так понимаю, жалуется на прерывания. На 5-ом прерывании у меня висит много
устройств (кроме этой карточки еще последовательный порт PCI-модема и видеокарта
GeForce 2MX-400), но ни в Linux ни в Windows это проблем не создает.

[rygoravich@rygoravich rygoravich] $ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
[rygoravich@rygoravich rygoravich] $

Т.е. никаких намеков на интерфейс локальной сети нет... Попытка насильной загрузки
модуля:

[rygoravich@rygoravich rygoravich] $ sudo kldload if_rl
kldload: can't load if_rl: Exec format error
[rygoravich@rygoravich rygoravich] $

???

[rygoravich@rygoravich rygoravich] $ kldstat
Id Refs Address Size Name
1 8 0xc0100000 2069ac kernel
2 1 0xc0307000 4c94 snd_ich.ko
3 1 0xc030c000 1983c snd_pcm.ko
4 1 0xc1276000 d000 ext2fs.ko
5 1 0xc12f1000 50000 nfs.ko
6 1 0xc1367000 3000 daemon_saver.ko
7 1 0xc136c000 15000 linux.ko
9 1 0xc15f1000 f000 miibus.ko
[rygoravich@rygoravich rygoravich] $

Загружен модуль miibus. Согласно докам он нужен для работы моей сетевой карточки.

[rygoravich@rygoravich rygoravich] $ sudo kldload if_rl
kldload: can't load if_rl: File exists
[rygoravich@rygoravich rygoravich] $

??? Так в выводе kldstat он не значился...

[rygoravich@rygoravich rygoravich] $ kldstat
Id Refs Address Size Name
1 9 0xc0100000 2069ac kernel
2 1 0xc0307000 4c94 snd_ich.ko
3 1 0xc030c000 1983c snd_pcm.ko
4 1 0xc1276000 d000 ext2fs.ko
5 1 0xc12f1000 50000 nfs.ko
6 1 0xc1367000 3000 daemon_saver.ko
7 1 0xc136c000 15000 linux.ko
9 2 0xc15f1000 f000 miibus.ko
10 1 0xc15eb000 6000 if_rl.ko
[rygoravich@rygoravich rygoravich] $

Откуда-то появился...

[rygoravich@rygoravich rygoravich] $ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
[rygoravich@rygoravich rygoravich] $

С сетевыми интерфейсами все по-прежнему...

Ядро перекомпилено, но с оригинальным тоже траблы.

Конфиг ядра:

=========начало#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.59 2004/04/07 20:29:01 vkashyap
Exp $

machine i386
# cpu I386_CPU
# cpu I486_CPU
# cpu I586_CPU
cpu I686_CPU
ident MYKERNEL
maxusers 0

#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols

# options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
# options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
# options UFS_DIRHASH #Improve performance on big directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
# options NFS #Network Filesystem
# options NFS_ROOT #NFS usable as root device, NFS required
# options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
# options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
# options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.

# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O

device isa
# device eisa
device pci

# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0

# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
# device atapifd # ATAPI floppy drives
# device atapist # ATAPI tape drives
# options ATA_STATIC_ID #Static device numbering

# SCSI Controllers
# device ahb # EISA AHA1742 family
# device ahc # AHA2940 and onboard AIC7xxx devices
# device ahd # AHA39320/29320 and onboard AIC79xx devices
# device amd # AMD 53C974 (Tekram DC-390(T))
# device isp # Qlogic family
# device mpt # LSI-Logic MPT/Fusion
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured

# device adv0 at isa?
# device adw
# device bt0 at isa?
# device aha0 at isa?
# device aic0 at isa?

# device ncv # NCR 53C500
# device nsp # Workbit Ninja SCSI-3
# device stg # TMC 18C30/18C50

# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
# device sa # Sequential Access (tape etc)
# device cd # CD
device pass # Passthrough device (direct SCSI access)

# RAID controllers interfaced to the SCSI subsystem
# device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
# device dpt # DPT Smartcache - See LINT for options!
# device iir # Intel Integrated RAID
# device mly # Mylex AcceleRAID/eXtremeRAID
# device ciss # Compaq SmartRAID 5* series
# device twa # 3ware 9000 series PATA/SATA RAID

# RAID controllers
# device aac # Adaptec FSA RAID, Dell PERC2/PERC3
#device aacp # SCSI passthrough for aac (requires CAM)
# device ida # Compaq Smart RAID
# device amr # AMI MegaRAID
# device mlx # Mylex DAC960 family
# device pst # Promise Supertrak SX6000
# device twe # 3ware Escalade

# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12

device vga0 at isa?

# splash screen/screen saver
pseudo-device splash

# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100

# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std

device agp # support several AGP chipsets

# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13

# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management

# PCCARD (PCMCIA) support
# device card
# device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
# device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable

# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9

# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da

# PCI Ethernet NICs.
# device de # DEC/Intel DC21x4x (``Tulip'')
# device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'')
# device txp # 3Com 3cR990 (``Typhoon'')
# device vx # 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
# device dc # DEC/Intel 21143 and various workalikes
# device fxp # Intel EtherExpress PRO/100B (82557, 82558)
# device pcn # AMD Am79C97x PCI 10/100 NICs
device rl # RealTek 8129/8139
# device sf # Adaptec AIC-6915 (``Starfire'')
# device sis # Silicon Integrated Systems SiS 900/SiS 7016
# device ste # Sundance ST201 (D-Link DFE-550TX)
# device tl # Texas Instruments ThunderLAN
# device tx # SMC EtherPower II (83c170 ``EPIC'')
# device vr # VIA Rhine, Rhine II
# device wb # Winbond W89C840F
# device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# device bge # Broadcom BCM570x (``Tigon III'')

# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
# device ed0 at isa? disable port 0x280 irq 10 iomem 0xd8000
# device ex
# device ep
# device fe0 at isa? disable port 0x300
# Xircom Ethernet
# device xe
# PRISM I IEEE 802.11b wireless NIC.
# device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
# device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
# device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
# device ie0 at isa? disable port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? disable port 0x300 irq 5 iomem 0xd0000
# device lnc0 at isa? disable port 0x280 irq 10 drq 0
# device cs0 at isa? disable port 0x300
# device sn0 at isa? disable port 0x300 irq 10

# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
# pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
# pseudo-device gif # IPv6 and IPv4 tunneling
# pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)

# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter

# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
# device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
# device ums # Mouse
device uscanner # Scanners
# device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
# device aue # ADMtek USB ethernet
# device cue # CATC USB ethernet
# device kue # Kawasaki LSI USB ethernet

# FireWire support
# device firewire # FireWire bus code
# device sbp # SCSI over FireWire (Requires scbus and da)
# device fwe # Ethernet over FireWire (non-standard!)

options PNPBIOS
========конец--
С уважением,
Rygoravich.
mailto:rygoravi***@o*****.info

-*Информационный канал Subscribe.Ru
Подписан адрес:
Код этой рассылки: comp.soft.bsd.all
Написать в лист: mailto:comp.soft.bsd.all-list@subscribe.ru
Отписаться: mailto:comp.soft.bsd.all--unsub@subscribe.ru?subject=comp.soft.bsd.all

http://subscribe.ru/ http://subscribe.ru/feedback